Parts & Accessories

Wheels Manufacturing Wave Washers help eliminate side play in cranks or pre-loaded angular contact bearings. Please refer to your crankset manufacturer's installation instructions for proper placement. - 24mm for Shimano Hollowtech II, FSA, Race Face EXI, SRAM GPX - 30mm for BB30, PF30, BB86, BB92 and other cranks with 30mm spindles - Uncompressed Thickness: 2.1mm - Compressed Thickness: 0.5mm - Spring Steel - 10 per bag

- Preload collar for adjusting tension on bottom bracket bearings - For Race Face 30mm Cinch System cranks only

Race Face aluminum chainring bolts for inner chainrings. Includes four 12.5mm bolts.

- Stock steel chainring bolts found on low/mid-range Race Face cranks - For double cranksets

Race Face CINCH Crank Puller • Puller cap for Cinch model Race Face cranks only, including Next SL, SixC and Turbine • Puller cap utilizes 16mm hex key • 26mm thread

Replacement crank bolt for RaceFace Cinch cranks.

Race Face steel crank bolt/puller for 2008 and earlier Evolve XC cranks.

Race Face Cinch aluminum crank arm bolt. 18mm, fits XC/AM cranks.

Race Face steel crank bolt/puller for Atlas AM cranks.

Replacement crank bolt and puller cap set for Race Face Cinch cranksets.

Race Face Crank Arm Tab Spacers • Spacers are used to protect the outer chainring tabs and enhance aesthetic when no outer ring or bashguard is used • Fits all Race Face cranksets • Use double bolts

Race Face aluminum Torx chainring bolt/nut set for double and triple chainrings. Includes four bolt sets.

Race Face aluminum Torx chainring nut/bolt set for triple chainrings. Includes four nut/bolt sets.

SRAM’s cranks are strong and tough, ready for any kind of ride. So it’s inevitable that pedal strikes and debris will chip away at the end of the crank. SRAM’s Carbon Crank Boot is an upgrade that combats the wear and tear that comes with hard riding. The boot protects the crank from surface damage and keeps the rider’s style perfectly intact.

- M30 cap with self-extracting crank bolt and washer - Compatible with 2013 and newer FSA Gossamer cranks

Use these Wheels Manufacturing Crank Spindle Spacers to adjust chainline or bearing play in bottom brackets. - 24mm for Shimano Hollowtech II, FSA, Race Face EXI, SRAM GPX - 30mm for BB30, PF30, BB86, BB92 and other cranks with 30mm spindles - Machined engineering-grade Delrin - 10 spacers per bag

SRAM’s cranks are strong and tough, ready for any kind of ride. So it’s inevitable that pedal strikes and debris will chip away at the end of the crank. SRAM’s Carbon Crank Boot is an upgrade that combats the wear and tear that comes with hard riding. The boot protects the crank from surface damage and keeps the rider’s style perfectly in tact. - Injection molded plastic crank arm protection - Perfect way to protect your carbon crank investment from scratches and dents from pedal strikes - Material: Injection molded plastic - Recommended Group: XX1, X01, XX, X0

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

- Adapts American/Pro BMX frames with a non-Threaded 51.3mm (2.02") i.d. bottom bracket shell to accept English-threaded bottom bracket & crank applications - CNC-machined aluminum with three steel connecting bolts to prevent independent rotation

- Octalink bolts include steel washers, JIS includes black plastic caps - HT2 mount bolts (low torque plastic, except XTR-M970 aluminum) are for mounting non-drive arm - Hollow bolts (SH-21504) not recommended for non-treated spindles

- Look, Zed, Chainring bolts

- Look, Zed, Chainring spacers

Slap on TruVativ's RockGuard and pin it through the rough. It's made from tough polycarbonate to take freeride and downhill abuse, and it's 4 bolt, 104 BCD compatible.

Machined engineering-grade Delrin inserts for adapting bottom brackets to a different type of crankset spindle. - Adapts PF30 and Cannondale BB30-73A bottom brackets for use with Hollowtech II cranksets - Delrin adaptors fit between bearings and crank spindle - BB Shell Width (mm): 68 mm , 73 mm - Spindle Interface Type: Hollowtech II - BB/Frame Interface: PF30

Wheels Manufacturing BB30 Bottom Bracket Adaptor for GXP Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on BB30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin.

Wheels Manufacturing Press Fit 30 Bottom Bracket Adapter for 22/24mm Spindle Cranks adapts 22/24mm Spindle Cranks (SRAM/TruVativ) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SRAM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SRAM to adapt 22/24mm Spindle Cranks (SRAM/TruVativ) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

The Wheels Manufacturing PressFit 30 Bottom Bracket Adaptor for Shimano Cranks adapts 24mm Spindle Cranks (Shimano Hollowtech II, FSA, Race Face EXI, etc.) to work on PF30 frames. Simply tap the adapters into the 6806 bearing in the BB shell, then install the spindle and cranks. Use Wheels Mfg Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. These spacers are machined from engineering-grade Delrin. Notes: - PF30-SHIM was originally designed for use with SRAM PF30 bottom brackets and will not work with Wheels Manufacturing PF30-BB, PF30-BB-AC or PF30-BB-CER. Use Wheels Mfg BBUNIV-SHIM to adapt 24mm Spindle Cranks (Shimano, FSA, etc.) in Wheels Manufacturing PF30 bottom brackets. - Not compatible with SRAM PF30 bottom brackets that use a thin plastic reducer inserted into the bearings. - The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

Wheels Manufacturing FSA PF30 Adapter for 24mm Spindle Cranks adapts 24mm Spindle Cranks (Shimano, FSA, etc.) to work on Pressfit 30 frames with FSA's PF30 bottom bracket installed. Simply tap the adapters into the 6806 bearing in the BB shell, install the spindle and cranks. Use our Crank Spindle Spacers to adjust your chainline, or take up any side-to-side movement in your cranks. - Machined engineering-grade Delrin - 48g/pr *NOTE: The stock bottom bracket seals must be removed before installing the Pressfit 30 adapter

Truvativ's BashGuard keeps your chainring(s) safe. It is designed to work with their BoxGuide chain guide (sold separately) for complete chain management. It's made from tough polycarbonate to take freeride and downhill abuse, and it's 4 bolt, 104 BCD compatible.

TruVativ's Stylo All Mountain Guard is all-mountain chainring protection with style. This 4mm thick aluminum guide is 4 bolt, 104 BCD compatible.