Tools

- Fits Truvativ GXP and Howitzer external-bearing bottom brackets with 16-spline/notched cups (also fits Shimano HollowTech-II bottom brackets) - CNC machined, heat treated steel construction - 1/2" ratchet drive and 32mm wrench flat tool interfaces

SRAM's Cable Cutter w/End Cap Crimper features sharp, spring-loaded diamond-shaped jaws and ergonomic handles to cleanly cut cables and housing every time. It also has jaws for crimping cable crimps. Plus, there's a safety clasp to keep this tool closed when not in use.

The Muc-Off Ultimate Tubeless Kit contains everything needed to get a tubeless-ready wheelset set up and ready to roll. Each Kit contains a Muc-Off Tubeless Rim Tape, Seal Patches, 2 CNC-machined black tubeless Valves and 2 pouches of No Puncture Hassle Tubeless Sealant. With 5 available kits for: Road/gravel/CX with shallow rims (44mm tubeless valves and 21mmx10m Rim Tape) Road/gravel/CX with deep rims (60mm tubeless valves and 21mmx10m Rim Tape) XC (44mm tubeless valves and 25mmx10m Rim Tape) DH/Enduro (44mm tubeless valves and 30mmx10m Rim Tape) DH Wide (44mm tubeless valves and 35mmx10m Rim Tape)

- Torx Tool Wrench 4Nm Preset

We went through extra steps to make this tool half precision measuring instrument and half pry bar. - Tolerances as tight as a quarter of a thousandth of an inch (.0063mm) in some critical dimensions of this tool. - Ability to lock in the feeler so you don't have to second-guess your measurement after bumping it on the tire. - Top half of tool will rotate out of the way of fender stays and frame tubes. - Feeler gauge stick stores inside the top half of the tool, very handy for the traveling mechanic. - T-bolt extends past the tool for access to those problematic hangers found on some modern full suspension bikes. - Compact at just under 11" ( 28cm) - Re-buildable - While ideally your HAG should be sent back for a rebuild, it is possible to do them in the field by replacing the brass bushing in the T-Bolt. - Compatible with the three most common wheel sizes (26, 27.5/650B, and 700/29)

This bottom bracket socket is for use with the Praxis M30 bottom bracket. Made with the same top-shelf aluminum alloy to the same exacting fit and tolerance as the rest of our socket range, these sockets won't chew up your shiny new bottom bracket.

Rear Shock Clamp Adapters - Connects rear shock tools to the RockShox Rear Shock Clamp Tool

For easy and safe servicing of your RockShox rear shock, look no further than the RockShox Rear Shock Clamp Tool. Use with model-specific clamp tips for servicing the damper of your rear shock. - For rear shock damper servicing - Ratcheting pistol grip action for easy operation - Use with shock-specific clamp tips

- T-handle shape to allow high torque transmission in difficult tightening and loosening situations. - Ergonomic shape of the handle fills the palm of the hand well, the fingers lie safely in the soft rounded handle recesses. - Bit holder for bits with 1/4'' hexagon drive - Rapidaptor technology for lightning-fast bit changes.

- Compatible for Manual and power tool socket insert (ISO 2725-Part 3) - "Take it easy" Tool Finder with color coding according to size - Featuring a good grip to allow easy pick-up even with oily hands. - Ball stop groove, for hex head bolts and nuts; chrome vanadium steel, matt chrome-plated.

- T-handle screwdriver: Shape to allow high torque transmission in difficult tightening and loosening situations. - The ergonomic shape of the handle fills the palm of the hand well, the fingers lie safely in the soft rounded handle recesses. - The whole hand makes contact with the handle and friction losses between the hand and the handle are avoided. - Holding function (HF) to securely hold the TORX screw on the tool. - Special surface treatment of the blades for high corrosion protection and an optimum fit in the screw head.

- Vinyl cushion-coated on long side for better grip (can be trimmed to expose hex for use) - Extra long for increased leverage (200mm)

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

The Abbey Bike Tools 4-way precision multi-tool is the perfect choice to carry with you while on a ride. We designed this beautiful green anodized tool to fit into a compact saddle bag, riding wallet, or tuck into a jersey pocket. Everybody makes a multi-tool and there's a little bit of everything on the market, so what's different about ours? All of the little things that add up to one nice little tool. A multi tool is only as good as it's tool engagement so that's where we started. If you're familiar with other Abbey tools you've no doubt noticed that they fit tighter than anything else out there and this one is no different. We use precision stainless steel bits that fit like a glove into the bolts on your modern bike. They wont strip out fasteners like the cheap offshore made tools that are so common in the bike world. They also won't rust into a ugly brown color after a season in a saddle bag. The next part of the multi-tool is the chassis, for this we used our favorite US drawn aluminum alloy and built a 4 position frame to hold the bits. At first glance the tool looks like it might be cumbersome but once you get it in your hand you realize how simple and effective the ergonomics of the tool are. Offering good leverage for all of the small fasteners on your bike, be it the precision adjustment of limit screws or adjusting the handle bars because you had one beer too many when you bolted them down late last night. Available in 5 pre-configured options or fully customizable to fit whatever mix of fasteners your bike requires. We suggest buying a tool for each of your bikes and leaving the tool stored away until needed. These little multi-tools are the result of a collaboration with fellow Bend OR residents, Argonaut Cycles and is the only American manufactured multi-tool for the bicycle market.

Standard bleed kit for mineral oil brakes - Includes 2 syringes/2 M4 fittings, bleed block, Torx tool, crowfoot - SRAM Model ID: DB-SPP-A0

- Easily determine seat tube size - Measures from 24mm to 31.8mm

- Ergonomic forged aluminum side plates. - Black forged Center-Pivot CrV bits wrapped. - Chrome Vanadium steel fastening hardware. - RAP 18/24/25: Cast stainless steel chain breaker with integrated spoke wrenches (HEX 8/10mm wrench, 4 spoke wrenches) - RAP 25: Lightweight aluminum Presta CO2 inflator. - RAP 24/25: Multi-function flat tool (bottle opener, DISC brake wedge, rotor trimming tool) - RAP 6: Hex: 3, 4, 5, 6mm; T25; Phillips - RAP 12: Hex: 2, 2.5, 3, 4, 5, 6, 8mm; T10, T25, T30; Flat; Phillips - RAP 18: Hex: 2, 2.5, 3, 4, 5, 6, 8mm; T10, T25; Phillips; quick link; steel chain breaker - RAP 24: Hex: 2, 2.5, 3, 4, 5, 6, 8mm; T10, T25, T30; Flat; Phillips; quick link; steel chain breaker; bottle opener - RAP 25: Hex: 2, 2.5, 3, 4, 5, 6, 8mm; T10, T25, T30; Flat; Phillips; quick link; steel chain breaker; CO2 inflator; bottle opener

- Tool for pulling and pressing bottom bracket bearings. - For all BB30 frames and bearings - Allows the bearing to be pulled without damage for cleaning and re-greasing - Also safely presses bearings back into cups - Instructions included

Magura Slotted Nut Bit is designed for use with brake lines. - 8mm slotted sleeve nut bit for tightening your brake hose sleeve nut to accurately compress hose fittings

- Used to install fork dust seals

The Drive Thru is a dummy hub or chain keeper that replaces your wheel while cleaning the chain. It is a fast and effective way to clean your chain between races or in your garage. It allows you to fully rotate your cranks and shift through your complete range of gears while protecting the frame. It installs simply with one hand, and is quick and easy to change between bikes. The Drive Thru is also great for packing the bike for transport.  - Note: This product is thread pitch dependent. You must order the same thread pitch as the thru-axle in your bike. - Dummy axle is precision-machined from 7075 aluminum and knurled for easy grip. - Pulley is machined from durable Delrin. - Oil and solvent-resistant O-ring - Lead-in threads designed for quick insertion into the frame - No tools required, simple, one-hand installation - Weight: 62 grams

The Crombie tool is a game changer when it comes to swapping cassettes. Whether you're a professional mechanic swapping cassettes several times a day or a DIY kind of guy, this gem has a place on your tool bench. The first time a quick release spring rolls under your bench the Crombie tool paid for itself. If you like to remove the cassette for a detailed cleaning or just swapping from one cassette to another, it's a big time saver and a breeze to use. This version of the tool has a Shimano/SRAM remover on one side with a Campagnolo on the other. A precision machined spline ensures maximum engagement and durability. The STANDARD version comes with a solid handle which gives the tool some mass making it the preferred choice in the shop. The SUPER LIGHT version shaves 125 grams out of the handle. SL handles are plenty durable for lockrings that are torqued close to the 40 NM spec. If you commonly come across over torque lockrings get the standard handle!

All the awesomeness of the dual-sided tool but in a single Shimano or Campagnolo version. Updated in 2020, the single-sided tool now has the same size handle (1/2 inch) as the dual-sided tool. - When purchasing the chain whip, buy the 1/2-inch handle chain whip.

- Premium non-solvent mobile cleaning unit - Using a proprietary natural bioremediation process, easily breaks down the heaviest of grime in seconds - Totally natural and safe for user, no hazmat labels in sight - Heats to an optimal temperature of 100.4° F/38° - Clean components with the integrated brush or use the soaking tank - Overheating security/reset feature - Easily drained: draining plug with integrated pour spout - Mobile: 4 integrated wheels, 2 with brake - Dimension: L32.3" x D20.9" x H41.3" - Weight: 51lb - Tank capacity: 40L/soaking area volume 4L (initial 40L NOT included) - Filters are not washable (initial filter included/preinstalled) - Bundle includes: 1 x 40 Liter Parts Washer, 2 x Eco Refill Fluid, 20 Liter, 1 x Eco Power Tabs

Replacement threaded cap for Abbey Hanger Alligment Gauge Tool.

For use with 1/2" Micro Bearing Press Shaft

Bottom brackets have some of the highest torque specs of any component found on a bicycle. Despite this, some bottom bracket cups feature tool fittings that allow mere millimeters of engagement, which can be a problem when attempting removal or installation. Solution: the Park Tool Bottom Bracket Tool Retaining System. Used in conjunction with nearly any Park Tool bottom bracket tool, the BBT-RS uses a spring-based tension system to apply consistent, adjustable pressure to the tool, ensuring full engagement with the tool fitting and preventing slippage. The BBT-RS can be configured for use with the vast majority of threaded and thread-together bottom bracket standards. The BBT-RS features an M8 threaded rod and a double-sided adapter nut with M12 and M15 threads, allowing it to thread directly into any compatible cartridge bottom bracket. The M15 adapter can also be used to install any of Park Tool's nine aluminum bottom bracket tools, all of which feature integrated threading for use with the BBT-RS. - Washer diameter: 57 mm (2.25") - Rod length: 175 mm (6.9") - Rod threading: M8 x 1.0 - Adapter nut threading: M12 x 1.0 & M15 x 1.0 Compatible with the following bottom bracket styles: - Threaded cup - Thread-together - Cartridge - Cup-and-cone Compatible with the following bottom bracket tools: - The following Park Tool socket-style aluminum bottom bracket tools: - BBT-27.3 - BBT-35-12 - BBT-35-36 - BBT-47-12 - BBT-47-16 - BBT-49.3 - BBT-59.3 - BBT-69.3 - BBT-79.3 - Wrench-style bottom bracket tools with a handle (e.g. Park Tool BBT-9, BBT-29, HCW-4) - Bottom bracket tools with external wrench flats (e.g. Park Tool BBT-19.2, BBT-22)

RockShox, 11.4115.129.010, Service Kit, Monarch Plus (does not include air can seals)

Performing the right maintenance on your SRAM and RockShox products not only ensures years of worry-free riding, but will also keep performance optimal and enhance your experience on the bike. Each service interval indicates the maximum number of riding hours designated for each type of recommended maintenance. Depending on the terrain and environmental conditions in your location, your riding style, and skill level, you may see more optimum performance if you service your SRAM and RockShox products at shorter intervals.

Wera ZyklopT-handle for higher torque transfer. For 3/8" square sockets with ball lock. Adjustable drive for more flexible usage. - 3/8" Zyklop T-handle with adjustable drive - For 3/8" square sockets with ball lock - High-quality chrome vanadium steel, matte chrome-plated - For higher torque transfer